Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Fast, Reliable Garage Door Parts Across Beverly
Garage door parts replacement in Beverly typically runs $110 to $340 depending on what failed, and most repairs are completed the same day we diagnose them. Salt air off Beverly Harbor corrodes cables, drums, and springs faster here than in Danvers or Peabody, so the part we replace on a Beverly door is often one that looked fine six months ago. We carry the parts on the truck, we show you the failed component before we quote, and we put the price in writing before any work starts. Call us at (970) 536-1724 and we’ll have a technician headed your way.
Why Servo Garage Doors Is Beverly’s Preferred Garage Door Parts Company
We work on a lot of Beverly doors, and we know what the salt air does to them. The Garage Door Parts we stock reflect that: high-cycle torsion springs, corrosion-resistant cables, and weatherstripping sized for the older openings in Beverly Farms and Prides Crossing carriage houses. Marcus Deller built Servo on a documentation rule from day one in 2015: the technician photographs the failed part before quoting a replacement. That is Clause 4 of The Haven Standard, and it means you see exactly what broke and why.
Every job gets a flat, written price and a written scope before we touch anything. That is Clause 1, and there are no exceptions. When we finish, you receive a documented photo record of what we found and what we did. Our technicians are background-checked and uniformed. And if a repair is not right, the 365-Day Done Right Promise means we make it right, backed by a terms page, not a handshake.
Our Garage Door Parts Services in Beverly

We stock the parts Beverly doors actually need, not a generic inventory. Here are the replacements we handle most often in the neighborhoods around Beverly.
Torsion Spring Replacement
A torsion spring replacement in Beverly runs $180 to $340. These springs sit on a shaft above the door and do the heavy lifting. Near the harbor, salt corrosion shortens spring life measurably. We install high-cycle springs rated at 25,000 cycles in coastal neighborhoods because the standard 10,000-cycle spring does not last here. Our techs replaced one on a Beverly Farms carriage house door recently where the spring had snapped clean at the coil after less than four years, typical for that exposure.
Safety note: torsion springs are under high tension and can cause serious injury if mishandled. Do not attempt to remove one yourself. Let a trained technician with the right winding bars and a torque-calibrated approach handle it.

Extension Spring Replacement
Extension springs run along the horizontal tracks on both sides of the door, and on older Beverly doors they are common. A pair typically runs $180 to $340 to replace, including safety cables if your current setup lacks them. Salt air attacks the spring coils and the anchoring hardware at the same rate. On older Cabot Street corridor garages, we often see extension springs that have stretched unevenly, leaving the door unbalanced and putting extra load on the opener.

Cables & Drums
Cable replacement in Beverly runs $130 to $250, and it is the repair we do most often within a mile of the water. Salt-laden air rusts the cable strands until they fray, then snap, usually mid-cycle. The drums that wind the cable corrode too, which is why we inspect both on every cable job. In Beverly Farms and Prides Crossing, our techs regularly see carriage-house doors where a snapped cable has whipped back against 100-year-old wood framing, causing secondary damage the original quote from an inland shop never accounted for.

Rollers & Hinges
Rollers wear out from use, but in Beverly the freeze-thaw cycle accelerates it. Water gets into the track, freezes overnight, and forces the rollers out of round. Replacement runs $110 to $220, and we always check the hinges while we are in there. On tight-clearance townhome garages off Rantoul Street, a worn roller dragging a track can make the whole door sound like it is coming apart. Nylon rollers run quieter and last longer than steel, and for most Beverly doors that is the right call.

What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterTrusted Brands We Service in Beverly
We service Wayne Dalton, Clopay, and Amarr doors across Beverly, along with every other major brand. The carriage-house doors in Beverly Farms skew heavily toward Clopay and Amarr models with custom panel sizes. If your door is a Wayne Dalton and the spring failed early, the salt air likely got to it; we replace it with a high-cycle spring that fits the existing hardware. We keep common Beverly parts on the truck so most repairs finish in one visit.
Common Garage Door Parts Problems We See in Beverly Homes

- Salt-corroded cables snapping mid-cycle. Within half a mile of Beverly Harbor and Salem Sound, cable strands rust from the inside out. The door jams partway up, and the cable on one side has usually already snapped by the time the opener stops. We replace both cables and the drums when this happens.
- Torsion springs breaking years early near the water. Moist salt air pits the coil surface and creates stress points. A spring rated for 10,000 cycles might fail after 6,000, which is why we install 25,000-cycle springs in Beverly Farms, Prides Crossing, and waterfront streets off Lothrop.
- Freeze-thaw cycles cracking bottom seals and heaving thresholds. Beverly’s harbor-adjacent winter temperatures hover right at freezing, so your bottom seal cracks, then icy water gets into the track. In tight-clearance garages, the resulting roller misalignment compounds quickly. Weatherstripping and bottom seal replacement runs $110 to $220.
- Rolling-code remotes losing signal on dense north-facing streets. Rooftop antennas, brick walls, and closely packed garages near downtown Beverly create more radio interference than open suburban blocks. Corroded opener receiver boards make it worse. Before replacing a remote, we test the logic board and antenna.
Pricing for Garage Door Parts in Beverly, MA
Here is what parts replacement costs in Beverly, quoted as flat written prices before any work starts.
| Parts Replacement | Beverly Price Range |
|---|---|
| Torsion Spring Replacement | $180-$340 |
| Cable Replacement | $130-$250 |
| Weatherstripping & Bottom Seal | $110-$220 |
What changes the number within those ranges: the spring’s wire diameter and cycle rating, how many cables need replacing, and how much of the bottom retainer has rotted out. We quote the exact price after seeing the door, and that price does not change once we start. Estimates are free, and if you have a written estimate from another company, bring it in. Our Free Second Opinion offer is exactly what it sounds like.
We Also Serve Cities Near Beverly

Our technicians cover Beverly and the surrounding North Shore, including Salem, Danvers, Peabody, and Lynn. If you are in one of those cities with a garage door that needs parts, the same written-price standard applies. Dispatch runs from our Boston office, and our crews serve Beverly locally.
Serving Beverly, MA - Our Local Coverage Area
We’re based in the Beverly area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Garage Door Parts in Beverly

A standard 10,000-cycle torsion spring near Beverly Harbor typically lasts 4 to 6 years instead of the 7 to 10 you would get inland in Danvers or Peabody. Salt air pits the coil surface and shortens the spring’s life. We recommend high-cycle springs rated at 25,000 cycles for any Beverly door within half a mile of the water, which pushes replacement intervals out to a decade or more. Call (970) 536-1724 and we can tell you what spring is on your door now and what it would cost to upgrade.
Salt-laden air from Salem Sound is corroding the cable strands, and once a few strands break, the rest follow quickly. One winter is fast, but it happens on northeast-facing doors with direct exposure to nor’easter spray. The fix is replacing the cables and drums together, using corrosion-resistant cable, and making sure the drum bearings are sealed. We did exactly this on a Wayne Dalton carriage-house door in Beverly Farms where the cables had failed twice in three years.
Yes. A panel replacement in Beverly runs $250 to $500, and we do it regularly on 6’6″ and 6’8″ carriage-house doors in Prides Crossing and Beverly Farms. The challenge is matching the panel to your specific Clopay or Amarr model and the existing paint line, plus managing the low headroom on many of these older openings. We measure, order the correct panel, and the written price includes installation. Call (970) 536-1724 for an exact quote, no obligation.
For a northeast-facing Beverly garage, we recommend a heavy-duty rubber bottom seal with a rigid aluminum retainer, not the vinyl strip most doors ship with. Nor’easters push wet snow directly at the door face, and freeze-thaw cracks vinyl quickly. Rubber stays pliable at lower temperatures and seals gaps better when the concrete threshold heaves. Replacement runs $110 to $220 installed, including the retainer if yours has rotted.
A torsion spring replacement in Beverly costs $180 to $340, quoted as a flat written price before any work starts. The range depends on the spring’s wire diameter and cycle rating. For doors near the harbor, we recommend the high-cycle option at the upper end of that range because it lasts twice as long in salt air. Call (970) 536-1724 for a free estimate, and if you have another company’s written estimate, bring it in for a Free Second Opinion.
Written by Marcus Deller, Owner at Servo Garage Doors, serving Beverly since 2015.






Before
After
Before
After